167 research outputs found
Thermal effects on geologic carbon storage
The final publication is available at Springer via http://dx.doi.org/10.1016/j.earscirev.2016.12.011One of the most promising ways to significantly reduce greenhouse gases emissions, while carbon-free energy sources are developed, is Carbon Capture and Storage (CCS). Non-isothermal effects play a major role in all stages of CCS. In this paper, we review the literature on thermal effects related to CCS, which is receiving an increasing interest as a result of the awareness that the comprehension of non-isothermal processes is crucial for a successful deployment of CCS projects. We start by reviewing CO2 transport, which connects the regions where CO2 is captured with suitable geostorage sites. The optimal conditions for CO2 transport, both onshore (through pipelines) and offshore (through pipelines or ships), are such that CO2 stays in liquid state. To minimize costs, CO2 should ideally be injected at the wellhead in similar pressure and temperature conditions as it is delivered by transport. To optimize the injection conditions, coupled wellbore and reservoir simulators that solve the strongly non-linear problem of CO2 pressure, temperature and density within the wellbore and non-isothermal two-phase flow within the storage formation have been developed. CO2 in its way down the injection well heats up due to compression and friction at a lower rate than the geothermal gradient, and thus, reaches the storage formation at a lower temperature than that of the rock. Inside the storage formation, CO2 injection induces temperature changes due to the advection of the cool injected CO2, the Joule-Thomson cooling effect, endothermic water vaporization and exothermic CO2 dissolution. These thermal effects lead to thermo-hydro-mechanical-chemical coupled processes with non-trivial interpretations. These coupled processes also play a relevant role in “Utilization” options that may provide an added value to the injected CO2, such as Enhanced Oil Recovery (EOR), Enhanced Coal Bed Methane (ECBM) and geothermal energy extraction combined with CO2 storage. If the injected CO2 leaks through faults, the caprock or wellbores, strong cooling will occur due to the expansion of CO2 as pressure decreases with depth. Finally, we conclude by identifying research gaps and challenges of thermal effects related to CCS.Peer ReviewedPostprint (author's final draft
Uncertainty in the Maximum Principal Stress Estimated from Hydraulic Fracturing Measurements Due to the Presence of the Induced Fracture
Abstract The classical theory for hydraulic fracturing stress measurements assumes an ideal case with a linear elastic, homogenous, and isotropic medium; and a fracture that reopens distinctly when the minimum tangential borehole stress is exceeded. The induced fracture disturbs this ideal picture in several aspects, which are important for the evaluation of the maximum horizontal principal stress using the fracture reopening pressure. This disturbance can be attributed to the fracture normal stiffness and the initial hydraulic fracture permeability. In this paper, the hydraulic fracturing reopening test is studied by coupled hydromechanical modeling that takes into account an induced fracture that is incompletely closed. The result shows that with realistic equipment compliance, the apparent fracture reopening evaluated from the well-pressure is close to the magnitude of the minimum horizontal principal stress with little or no correlation to the maximum horizontal principal stress. This observation suggests that determination of maximum principal stress by hydraulic fracturing using the reopening pressure is very uncertain
Recommended from our members
The Influence of an Interlayer on Dual Hydraulic Fractures Propagation
Multi-cluster hydraulic fracturing of long-range horizontal wells is an approach for enhancing the productivity of low-permeability shale reservoirs. In this study, RFPA-Petrol (rock failure process analysis on petroleum problems) is applied for modeling hydraulic fracture propagation in multilayered formations. RFPA-Petrol based on coupled hydraulic-mechanical-damage (HMD) modeling was first tested by modeling a laboratory scale experiment on a physical (cement) model with a single completion. The modeling demonstrated the capability of RFPA-Petrol for simulating hydraulic fracture propagation. Then, we used RFPA-Petrol to investigate how the difference in material properties between oil-bearing layers and interlayers and the fracturing fluid properties influence the propagation of dual fractures in multilayered laboratory-scale models. In this case, the models with geological discontinuities in the vertical direction are strongly heterogeneous and RFPA-Petrol simulations successfully modeled the fracture configurations
Recommended from our members
Discrete dilatant pathway modeling of gas migration through compacted bentonite clay
A coupled multiphase fluid flow and discrete fracturing model is applied to simulate bench-scale gas migration experiments on compacted bentonite. The numerical modeling is based on the linking of the multiphase fluid flow simulator TOUGH2 with a Rigid-Body-Spring Network model, which enables a discrete (lattice) representation of elasticity and individual fractures. The evolution of a complex network of dilatant flow paths is modeled through opening and breakage of lattice interface bonds between porous-elastic matrix elements. To achieve a good match with the experimental results, including an abrupt gas breakthrough along with pressure and stress responses, it was necessary to calibrate model parameters for (1) air-entry pressure, (2) shear and tensile failure of lattice interface bonds, (3) moisture swelling/shrinkage effects on stress, and (4) aperture-dependent permeability of dilatant flow paths. Our best-fit conceptual model considers a pervasive network of discrete flow paths propagating from the gas injection point, whereas some of the experimental data indicate the potential for heterogeneous and unstable flow paths
Recommended from our members
Large releases from CO2 storage reservoirs: Analogs, scenarios,and modeling needs
While the purpose of geologic storage in deep salineformations is to trap greenhouse gases underground, the potential existsfor CO2 to escape from the target reservoir, migrate upward alongpermeable pathways, and discharge at the land surface. In this paper, weevaluate the potential for such CO2 discharges based on the analysis ofnatural analogs, where large releases of gas have been observed. We areparticularly interested in circumstances that could generate sudden,possibly self enhancing release events. The probability for such eventsmay be low, but the circumstances under which they occur and thepotential consequences need to be evaluated in order to designappropriate site-selection and risk-managementstrategies. Numericalmodeling of hypothetical test cases is suggested to determine criticalconditions for large CO2 releases, to evaluate whether such conditionsmay be possible at designated storage sites, and, if applicable, toevaluate the potential impacts of such events as well as designappropriate mitigation strategies
A comparative simulation study of coupled THM processes and their effect on fractured rock permeability around nuclear waste repositories
Abstract This paper presents an international, multiple-code, simulation study of coupled thermal, hydrological, and mechanical (THM) processes and their effect on permeability and fluid flow in fractured rock around heated underground nuclear waste emplacement drifts. Simulations were conducted considering two types of repository settings: (a) open emplacement drifts in relatively shallow unsaturated volcanic rock, and (b) backfilled emplacement drifts in deeper saturated crystalline rock. The results showed that for the two assumed repository settings, the dominant mechanism of changes in rock permeability was thermalmechanically-induced closure (reduced aperture) of vertical fractures, caused by thermal stress resulting from repository-wide heating of the rock mass. The magnitude of thermal-mechanically-induced changes in permeability was more substantial in the case of an emplacement drift located in a relatively shallow, low-stress environment where the rock is more compliant, allowing more substantial fracture closure during thermal stressing. However, in both of the assumed repository settings in this study, the thermalmechanically induced changes in permeability caused relatively small changes in the flow field, with most changes occurring in the vicinity of the emplacement drifts
- …